Welcome Fall with Heated Copper

08/31/2014

Welcome Fall

Hello everyone.  Hard to believe it is the last day of August.  Where has the summer gone?

In my area, there is an annual Apple Festival and the yummy cider brings thoughts of Fall to my mind and to my post for your today.  I used a heated copper technique thanks to a friend who had some spare copper roll.

I wanted to showcase how Poppystamps dies can be used to cut thin (.003) copper sheeting so I used three different dies and ended up with my main card and two additional variations.  I hope you enjoy!

I cut an A2 card as a top fold.  Next I cut a smaller darker brown rectangle and ran through an embossing folder to create the wood-grain texture before moving onto heating the copper.  

In order to heat copper, you must have a heat proof surface.  I used an old half-sheet baking pan flipped over.  I  used a mini-torch (think Creme Brulee kitchen torch) as my heat source.  After it cooled, I carefully cut it with a paper trimmer.  The edges can be sharp so be careful not to get cut. It is a good idea to heat the copper outside if using a butane mini torch. 

I had a few missteps in running the dies through.  The frame around the leaves is very delicate and stuck to my cutting plates. Then I thought to add a piece of cardstock below the copper, then the copper and then the [1064] Maple Leaf Poppystamps die.  I ran through my Big Shot a couple times in order to be assured a clean cut as the copper is thicker than cardstock.  Problem solved!  It didn't stick to the cutting plates.  You can simply (but carefully) peel back the cardstock and you have the copper ready to adhere to your card.

Your could use foam adhesives to give some height or glue circles or hot glue.  I used a combination of glue dots and foam adhesive squares to adhere to the card.  Inside, not shown, I simply put a vanilla color of cardstock and stamped [CS308B] Thank You So Much greeting from Poppystamps.

My second example with heated copper is a Christmas card using [1056] Viviro Ornament and [CS307B] Holidays Sparkle Cling Stamp with [1005] Classic Ribbons Die.

The last example uses a the [1028] Delaney Butterfly Poppystamps Die against a plain black background.  This card is quite flexible and can be used for a thank you, sympathy or even to say hello.  

This will be one of my last posts as part of the Poppystamps Design Team.  I will be stepping down in September.  I want to thank Poppystamps for the wonderful opportunity to be part of their Design Team for the last 12 months.  I have made a lot of friends among the talented ladies on the team and hope that I have inspired some of you to get crafting with Poppystamps.  I appreciate each of you taking the time to stop by the Poppystamps blog and view my creations. 

Have a wonderful Autumn and Holiday season.

Viviro Ornament	[CS307B] Holidays Sparkle	[1005] DIES- Classic Ribbons	Maple Leaf
Delaney Butterfly

Spooky Nights

08/23/2014

Spooky Nights

I recently received a black cat candy jar as a gift from a dear friend.  This provided me the inspiration to create a spooky sky under which black cats prowl.  

For the sky, I used a brayer and a light pink inkpad to cover white cardstock that would become the front of the card.  Next I used the brayer and covered most of the cardstock with a light purple ink. After which I switched to a sponge and sponged on a medium blue, followed by a dark blue and then by dabbing dark purple. 

Then I used the Poppystamps Puffy Clouds Border [1099] cut diagonally across card stock to give a different look to the clouds.  To add a bit of fog to the sky, I used a bright white ink and sponged around the mask and alternated with sponging the dark purple.

After the sky was done, I drew two hills and cut them out with scissors and adhered them to the card with foam squares to give dimension.  Carefully, I tucked sections of the Poppystamps Brevilla Houses [1009] behind the green hills and adhered with foam adhesives.

Then I proceeded to cut out the Poppystamps Antique Lamp Post [858], the cats (Poppystamps Sitting Cat [860], Walking Cat [859] and Curious Cat [872]).

For the moon, I drew a circle and cut it out and adhered it with my glue pen.

Next, I cut out the Poppystamps Fireplace Logs [1072] logs with brown cardstock and the Poppystamps Warm and Cozy Fire [1070] in white cardstock.  To create the flames, I colored the white cardstock with Copic markers.

 I decided to add a bit of Halloween to the scene by using BOO from the Poppystamps Scary Background Die [1078]. I used a glue pen and put the letters on a diagonal and slightly off-center to give it more of a spooky look.

Supplies:

Poppystamps Scary Background Die [1078]

Poppystamps Puffy Cloud Border Die [1099]

Poppystamps Brevilla Houses [1009]

Poppystamps Fireplace Logs [1072]

Poppystamps Warm and Cozy Fire [1070]

Poppystamps  Sitting Cat [860]

Poppystamps Walking Cat [859]

Poppystamps Antique Lamp Post [858]

Poppystamps Curious Cat [872]

Cardstock for base and for scene.

Adhesives

Ink (and lots of it) pink, light purple, medium blue, dark blue, dark purple, white

Thanks for stopping by!

  

Puffy Cloud Border	[1078] DIES- Scary Background	[1009] DIES- Brevilla Houses	[1072] DIES- Fireplace Logs
[1070] DIES- Warm and Cozy Fire	[860] DIES- Sitting Cat	[859] DIES- Walking Cat	Antique Lamp Post
[872] DIES- Curious Cat